![]() ![]() Tries to reload an icon or cursor resource from the original resource file rather than simply copying the current image. Valueĭeletes the original image after creating the copy. This parameter can be one or more of the following values. If this is zero, then the returned image will have the same height as the original hImage. The desired height, in pixels, of the image. If this is zero, then the returned image will have the same width as the original hImage. ![]() The desired width, in pixels, of the image. This parameter can be one of the following values. If necessary, the function stretches the bits to fit the desired size of the new image. Despite the large advertisement banners for these partition tools on google, they all failed.Creates a new image (icon, cursor, or bitmap) and copies the attributes of the specified image to the new one. Note: I tried to do the partition changes on a Windows PC, using different partition tools, but they all failed with strange "Disk IO error" messages, although the SD card is clearly ok. If it failed, you still have the old card as a backup. If everything worked well, your Pi has now much more disk space to play around with.Once the Pi has booted open gparted again, and now extend the root partition to fill the whole remainder of the disk.Now shut down the pi, and insert the new SD card into the SD card slot of the Pi.For safety, we make sure the existing state boots first, though. Note: Now the root partition still has the old size, but we could extend that now.Extend the size of the extended partition to fill the whole disk.This is a container for three other partitions: settings, boot and root (we want to extend the root partition, as this is the one that contains all user data and applications, but we cannot directly do that, because it's limited within that container partition) On the new disk, select the partition which has "extended" in the file system.When it's done, open gparted again, and check that you'll now have the same partitions on the source and the target disk.Use sudo dd if=/dev/mmcblk0 of=/dev/sdb bs=4M status=progress to clone the existing disk to the new SD card.Accept those changes, then close gparted.Unmount any volumes and delete all partitions from /dev/sdb (right click on the partitions to get a menu).The drop-down at the upper right will have two entries, one named /dev/mmcblk0 (that's the SD card the Pi now booted from) and one named /dev/sdb or similar, which is your new card.Insert the new card into an external card reader and attach it to the Pi.I was going from a 32GB SD-Card to a 128 GB Card. The following worked for me, with an SD card that was originally prepared with NOOBS. How do I transfer my setup between SD cards?.How can I resize my / (root) partition?.Find the root, stretch it, resize the filesystem and enjoy your new space (and a 16GB image you need to back up). Note that depending on your distribution of choice and version, the card may be set up in different ways and the instructions might not be correct to the letter. This should all work from the running Linux system on the PI, so as long as you can get the image on the card correctly in windows, it shouldn't be a problem anymore. Raspi-config can apparently also do this automatically.Įssentially you should be able to use parted, fdisk, cfdisk or other tool to resize the root partition and use resize2fs to make the filesystem use the extra space. There's also a page on resizing partitions on rpi. Some instructions on how to set up a card image can be found on the RPI wiki "easy SD card setup". Once you get a second card and as long as you don't destroy the original one, it should be easy to experiment. I think you should look into doing this so you can take and restore backups of your card from time to time. Im open to any suggestions, just would rather not have to start from scratch with a fresh raspbmc install. I suppose I could load raspbian on the 2GB after I copy the image to the 16GB to get a more functional linux box but hopefully that's more work then necessary. The problem is, I only have windows PC's available to me. Is this possible without deleting the contents of that partition? Looking here I see that the ext4 partition at /dev/mmcblk0p3 is the one that would need re-sizing. ![]() However this would then leave only 2GB available to the pi on the 16GB correct? Essentially I am wondering how one would go about re-sizing the partition to use all of the available space on the 16GB SD. ![]() My first thought is use Win32 Disk Imager to read from the 2GB and then write to the 16GB. I now I have a 16GB class 10 in the mail and am wondering how to go about copying my current setup to that SD. I loaded raspbmc and then spent time loading repositories, add-ons and customizing to my liking. I couldn't hold off playing with it so it had to do for the time being. So I got my new pi and the only free SD I had was 2GB. ![]()
0 Comments
Leave a Reply. |